tation within this manual, Danfoss makes no warranty or This manual can be used with all VLT AQUA Low Harmonic Drive frequency converters with software . MAKING MODERN LIVING POSSIBLE. Operating Instructions. VLT. ®. AQUA Drive FC kW 2 Aug This publication contains information proprietary to Danfoss. By accepting and VLT® AQUA Drive High Power Instruction Manual MG
|Published (Last):||16 October 2017|
|PDF File Size:||18.26 Mb|
|ePub File Size:||16.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
Choose General Settings. Operation keys and LEDs. If contacting Danfoss Service, make sure to mention the number and alarm description.
This is done by using the supplied installation devices in the adjustable frequency drive. The packaging for these enclosures contains, as shown: How to operate the adjustable frequency drive [Main Menu] is used for programming all parameters.
This is because the sine danfoss vlt aqua drive manual of the motor current is almost perfect at high switching frequency. Select All from LCP. Terminal number 12, 13 Max. If this is done, it will reduce the RFI performance to A2 level.
Select My Personal Menu to display only the parameters, which have been pre-selected and programmed danfoss vlt aqua drive manual personal parameters. Input 29 [Hz] Actual value of the frequency applied at terminal 29 as a pulse input. Expanding an existing network. Par to contain a fault log that can be read out.
The adjustable frequency drive is about to cut out because of an overload too high current for too long. Reconnect the line power supply – the adjustable frequency drive is now reset. Insert the other end in terminal 12 or A description of the alarm can be found in the Troubleshooting section.
Only display parameters selected in par and danfoss vlt aqua drive manual can be viewed. Safety, policy and warranty. Use the meter More information.
Use [Status] for selecting the mode of display or for changing back to display mode from either the quick menu mode, the main menu mode or alarm mode. Only par or will be displayed depending on other parameters set in the Main Menu, and depending on default settings specific to global geographical locations.
Terminal number 50 Output voltage Incorrect mounting of screws Step 2B: This is useful in applications in which the driven load must first quickly accelerate to a minimum speed when it manuxl started. Disconnect DC bus terminals 88 and Wait at least as long as the time mentioned in section Remove motor cable.
Via a digital input with danfoss vlt aqua drive manual Reset function.
Manuel d installation Installation manual. Go to career section Working at Danfoss. Contents Contents 1 Introduction 3 1.
Tightening of screws Step 4: Meter Step Size 0. It will also show the user how to.
The GLCP is divided into four functional groups: The adjustable frequency drive is equipped with internal overcurrent protection that can be used for upstream overload protection UL applications excluded. The [ ] key increases the value, the [ ] key decreases the value. Mary Danfoss vlt aqua drive manual 2 years ago Views: A motor that has been stopped may start if faults occur in the electronics of the adjustable frequency drive, or if a temporary overload or a fault in the supply line or the motor connection ceases.
Find the related danfoss vlt aqua drive manual documentation.
If an alarm cannot be reset, the reason may be that its cause has not been rectified, or that the alarm is trip-locked see also the table on following page.
The adjustable frequency drive manuql into alarm mode and the display shows that the AMA was terminated by the user. Here is the basics. Thyristor power units and Solid state contactors TC series Two-phase control of a three-phase load or control danfoss vlt aqua drive manual two single-phase loads User Manual Copyright Eurotherm Automation All rights reserved.
The up key increases the value, and the down key decreases the value. It is possible to switch danfoss vlt aqua drive manual between Main Menu mode and Quick Menu mode. This will eliminate the need for an extra communication network.
Check that the configuration – Interval between Starts is enabled. The fault could be a result of: