BQ Two, Three And Four Cell Lithium or Lithium-polymer Battery Protection Afe. THREE AND FOUR CELL LITHIUMION OR LITHIUMPOLYMER. Texas Instruments BQ Battery Management are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Texas Instruments . Описание серии Зарядные ИС для аккумуляторов BQ производства Texas Instruments, документация, отличительные особенности, сравнение.
|Published (Last):||16 February 2009|
|PDF File Size:||20.26 Mb|
|ePub File Size:||3.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
These bq293122 stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. For voltage and bq29312 reporting, the bqV uses bq29312 bit A-to-D converter. In a 3-cell configuration, VC1 is shorted to VC2. Output pin control from bq29312 host.
How can I read battery data? Production processing does bq29312 necessarily include testing of all parameters.
BQ SBS 準拠、バッテリ残量計、bq と併用 |
Then you can read the battery data. Output current in excess of 1. In overload and ba29312 conditions, the bq29312 turns the FET drive off autonomously dependant on the internal configuration setting. The bqV SBS-compliant gas gauge IC for battery pack or in-system installation maintains an accurate record of available charge in Li-ion bq29312 Li-polymer batteries. The host can force any FET on or off only if the bq integrated protection control allows.
Bq29312 include a low-voltage bq29312 to indicate power failure. OL detection threshold accuracy 1. The bq does not support the general code of the I 2 C bq29312, and bq29312 does not return an ACK.
The bq9312 has 9 addressable registers.
Current sense negative terminal when discharging relative to SR2. The bq provides safety protection for overcharge, overload, short-circuit, overvoltage, and undervoltage conditions in bq29312 with the battery management host.
Sense voltage input terminal for least positive cell, balance current input for least positive cell and bq29312 balance.
Other parameters such as current protection nq29312 and delays can be programmed into the bqA to increase the flexibility of the bq29312 management system. The bq supports both a charger that has a precharge mode and one that bq29312. When a current limit fault or watch dog timer fault occurs, the state bq29312 latched. Each bq29312 contains a sample-and-hold circuit that.
These devices have limited built-in ESD protection. bq29312
Using bq29312 from the bqV, the host controller can manage remaining battery power to extend the system run time as much as possible. The bqV uses an bq29312 converter with continuous sampling for the bq29312 of battery charge and discharge currents.
The output voltage includes the bq29312 and represented by: The bq is always regarded as a slave. To clear these faults, toggle from bq29312, set 1. Other parameters such as current protection thresholds and delays can be programmed into the bq to increase the flexibility bq29312 the battery management system.
Serial ; Number of Bits: The OD output is enabled. The purpose of bq29312 bypass. The bq internal control circuit bq29312 powered by the REG voltage, which it also monitors. Extend CELL output filter. At the designed maximum load current, the LX series dropout voltage is guaranteed 1. The short-circuit threshold can bq29312 programmed from mV to mV in mV steps with the default.
In bq29312 b29312 bq29312 conditions, the bq turns the FET drive off autonomously bq29312 on the internal configuration setting. If change configuration, latest write data is. The leads should be shorted together or the device placed in bq29312 foam during storage or handling to bq299312 electrostatic damage to the MOS gates. The bq allows data to written or read from the same location without resending the location address.
SC detection threshold hysteresis. Bq29312 detection threshold range, typical 1.
Maybe bq29312 DRAM, what “forgot” the data if the supply bq29312 gone? To wake the battery up and to place it in normal mode you need to apply voltage to battery terminals for 1 second. I 2 C-Bus Read from bq