24LC256 PDF

This part can be programmed by Digi-Key; for details please contact our custom department at x or @ 24LCI/P Microchip Technology EEPROM 32kx8 – V datasheet, inventory, & pricing. 24LCI/ST Microchip Technology EEPROM 32kx8 V datasheet, inventory, & pricing.

Author: Kagalar Yozshuzilkree
Country: Pakistan
Language: English (Spanish)
Genre: Career
Published (Last): 10 October 2005
Pages: 115
PDF File Size: 8.32 Mb
ePub File Size: 3.86 Mb
ISBN: 482-2-85730-290-4
Downloads: 2457
Price: Free* [*Free Regsitration Required]
Uploader: Vorg

However, if the address pins wereit would be 0x The clock is used to synchronize data transfer to and from the device between the arduino microcontroller and the EEPROM chip. In this circuit, we will show how to connect a 24LC to an arduino and how to program the arduino so that it can write to and read from the 24LC chip.

We then create a for loop where we write out 5 ‘2’s representing a zip code. Just remember that when you connecting multiple devices, each one must be unique.

24LC256 Serial I2C EEPROM 256K

The WP pin stands for write-protected and this allows you to control if data can be written to the eeprom or not. Time 2lc256 move on to software! This variable is not required but it allows us to easily change the address we want to access without going through all of the code and replacing the value.

If it wasit would be 0x This means our 24LC chip gets the address and then which tells it to store the next byte in address location 20, The SDA pin, pin 5, is the serial data pin. We first call the Wire.

The SCL pin, pin 6, is the serial clock line. The datasheet for the 24LC can be found at the following link: After our data and power pins are connected we have four left on 24LC chip, the WP pin and the three address pins.

Therefore, we put all the functions in the setup function and not in the loop function. These are the hardware connections. Even with only being used, an address still must be used.

Access Denied

And we connect GND, pin 4, to power ground. Next we have to send the address on the eeprom we want to write to. Or you can connect it to a digital pin of a micrcontroller, so that you can switch between enabling or disabling it.

Next we do a bitwise AND to get just the last eight bits. The next three bits A2,A1,A0 are the important bits 24lc2566 we can change so lets look at the simple table below to see what address the chip 24lc26 have depending on what we set these pins to. Since this is I 2 C communication, we have to create a Wire object.

First, to power the chip, we connect V CCpin 8, to 5V. Using the image above as a guide lets begin to wire the chip.

Then connect the SCL pin 6 to pin 5 on the Arduino. The address input pins, A0, A1, and A2, are for multiple device operation. Finally we have to pass along the byte we want to store. Next we start off just like we did with the write function by starting the process with beginTransmission and then we send the address we want to access; this works exactly the same way as the write function. Therefore, the address pins will have a value of The next function requestFrom sends the command to that chip to start sending the data at the address we set above.

We need to send the MSB Most significant bits first so we have to shift our address to the right eight bits. The arguments it accepts are the same first two arguments the write function, the device address and the address on the eeprom to read from.

The possible 24lc2256 are,,and If you are using Arduino 1. The first send function takes the eeaddress and shifts the bits to the right by eight which moves the higher end of the 16 bit address down to the lower eight bits. For more information please read http: Next, we have our setup function. In 24c256 circuit, we’re not interested in disabling the write feature. Next lets go ahead and connect the data pins to the Arduino board. This tutorial was originally posted on the 10kohms.

24LC Serial I2C EEPROM K | Microchip

This means you can turn off a device, keep it off for 3 days, and come back and turn it on and it can still run the program that was programmed in it. This establishes a clock line so that the master and slave device can work in synchrony. Arduino Sketch Below is the entire tutorial code, scan over it and see if you understand it before I dive into what each section does. We then create a serial monitor so that we can see our Serial.

The pinout of this chip is shown below. Read operations, however, are not affected.